User manual RAYMARINE RC435

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RAYMARINE RC435. We hope that this RAYMARINE RC435 user guide will be useful to you.


RAYMARINE RC435 : Download the complete user guide (1801 Ko)

Manual abstract: user guide RAYMARINE RC435

Detailed instructions for use are in the User's Guide.

[. . . ] RC435 & RC435i Chartplotters Owner's Handbook Document Number: 81236-2 Date: August 2004 ii RC435 and RC435i Chartplotters iii About this Handbook Introduction This handbook describes the RC435 Chartplotter with external GPS antenna and RC435i Chartplotter with internal GPS antenna. The RC435 and RC435i utilize Satellite Differential (SD) signals for enhanced navigational accuracy. The RC435 and RC435i GPS Chartplotters are waterproof and therefore can be installed above deck. The equipment is comprised of: · 6 in Color LCD display with Chart holder compartment for a Navionics Gold Chart electronic chart card · Low profile external GPS antenna for the RC435 · Internal GPS antenna for the RC435i ® The RC435/435i Chartplotters can output GPS and Waypoint data to operate with other equipment, such as an autopilot or repeater instrument connected via the NMEA 0183 interface. [. . . ] The alarm is set to OFF on power up. XTE Alarm The selected value is used as the cross track error limit. The alarm is triggered when the cross track error exceeds the selected limit when a GOTO or a Route Follow is in progress and an alarm message is displayed. Select Chart Use SELECT CHART to access different charts from the same Gold Card. 1G737T32-FLORIDA SE LOAD CHART "ENTER" TO LOAD "CLEAR" TO QUIT D6249-1 Use the trackpad up/down buttons to select the desired chart and press ENTER to load this as the active chart. Note: Only one chart can be active at any one time. Chart Text When ON, Chart text (such as place names) are shown on the screen. The selected setting is retained when the unit switched off. Chapter 4: Setting Up 43 Chart Boundaries When ON, Chart boundary lines are shown on the screen. The selected setting is retained when the unit switched off. Safety Contours Set to display safety contours of less than 2, 5, 10 and 20 meters or set to OFF. The selected setting is retained when the unit switched off. Depth Contours Set to display depth contours of 5, 10 and 20 meters, set to ALL to show all contours or set to OFF. The selected setting is retained when the unit switched off. Spot Soundings When ON, spot soundings are displayed. The selected setting is retained when the unit switched off. Light Sectors When ON, light sectors are displayed. The selected setting is retained when the unit switched off. Presentation Set to display navigation mark in either INTERNATIONAL or US symbology. The selected setting is retained when the unit is switched off. Position Calibration When ON, all position data is offset from WGS 84 by the value of the selected calibration. The default calibration offset is zero. To perform position calibration: 1. The menu is removed and a single function and help text are shown: D4713-1 44 RC435 and RC435i Chartplotters 3. The distance and bearing of cursor from vessel is displayed in the Status Bar as BRG and RNG. Press CLEAR to reset the value to zero and return to the Chart Set Up menu. --or-- Press ENTER to confirm the selected offset value. You are returned to the Chart Set Up menu with POSITION CALIBRATION set to ON. Position data is followed by "(c)" to indicate that the calibration offset has been set. An offset of 2nm or less is applied to all position data equal to the range and bearing between the WGS 84 position and the position entered. Note: Pressing ENTER with a selected offset of more than 2nm gives a warning message which is cleared on any key press. The Calibration Set Up mode maintains and the user can either reselect an acceptable offset or press CLEAR to reset the value to zero and return to the Set Up menu. 4. 4 GPS Setup The GPS set up page provides information for the status of the tracked navigation satellites plus HDOP and satellite Fix Status. It also provides the ability to select the SD satellite and to reset the GPS system. To select GPS Set Up: 1. Use the trackpad to highlight the GPS SET UP function and press ENTER to display the GPS STATUS screen and soft key. GPS STATUS is displayed. Chapter 4: Setting Up 45 GPS STATUS 0 0 0 0 0 0 0 0 0 0 0 122 HDOP 0 FIX STATUS 1. 0 SD-GPS ENABLE RESET GPS SD-FIX D6250-1 D6253-2 Figure 4-3: GPS Status Screen and Soft Key The GPS STATUS screen provides, for each tracked satellite, the satellite number, a graphical signal strength bar, status, azimuth angle and its elevation angle from your vessel. [. . . ] 2333. Chapter 6: Maintenance & Troubleshooting 109 Technical Service is available Monday through Friday 4:00 AM to 6:00 PM Eastern Time. Please have the Raymarine item or part number ready when calling if placing an order. If you are not sure which item is appropriate for your unit, you should first contact the Technical Support Department to verify your requirements. Technical Support For technical support, call: 1-800-539-5539 ext. Our Technical Support Specialists are available to answer questions about installing, operating and trouble-shooting all Raymarine products. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RAYMARINE RC435




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RAYMARINE RC435 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.