User manual RAYMARINE SL PLUS CHARTPLOTTER DISPLAYS

[. . . ] SL520/530/631 PLUS Chartplotter Display Owner's Handbook Document number: 81209_1 Date: September 2002 iii SL520/530/631 PLUS Chartplotter Display Owner's Handbook September 2002 INTENDED USE The display units detailed in this handbook may form part of navigational radar systems intended for light marine use. These displays and radar systems are only an aid to navigation. SAFETY NOTICES This equipment must be installed and operated in accordance with the instructions contained in this manual. Failure to do so can result in personal injury and/or navigational inaccuracies. Adjustments require specialized service procedures and tools only available to qualified service technicians ­ there are no user serviceable parts or adjustments. [. . . ] Press the INSERT WAYPOINT soft key to place the waypoint below the selected position in the Route. To remove a waypoint from the New Route column, highlight the waypoint and press the REMOVE WAYPOINT soft key. Notes: (1)A waypoint cannot be used more than once in a route; those already used are displayed in a lighter shade of gray. Notes: (2)The INSERT WAYPOINT or REMOVE WAYPOINT action adds/removes the highlighted waypoint to/from the Route column, regardless of which column is selected. When all waypoints have been entered, press the ACCEPT ROUTE soft key (or ENTER) to complete the route. Note: The completed route is stored in the display unit and will be re-displayed if you turn the unit off then on again. However, on an integrated system it is possible for a current route from another unit to overwrite this route; it is therefore recommended that you save the route, as described in Saving the Current Route on page 3-22. Creating a New Route 3-22 SL520/530/631 PLUS Chartplotter Displays Saving the Current Route You can save up to 20 named routes in the route database list. When you save the route, all new waypoints are saved in the Waypoint List. Note: If the current route has not been saved, when you attempt an operation that affects this route, e. g. To access the SAVE ROUTE soft key, press the ROUTE soft key, followed by MORE. The save route pop-up and the NAME ROUTE soft keys are displayed as illustrated in Figure 3-6. (If required, you can use the trackpad to select another position in the list; this can be a blank slot, or an existing route that you no longer require). SAVE ROUTE 1 2 3 4 5 EMPTY EMPTY EMPTY EMPTY EMPTY SAVE ROUTE Saving the Current Route NAME ROUTE?If you do not wish to name or re-name the route, press the NO soft key to clear the list. Use the trackpad to move the cursor right or left to the character you wish to edit. Then use the top or bottom of the trackpad to increase or decrease the letter or number. Chapter 3: Standard Chart Operations 3-23 You can use a Navigator Keypad (see Using the ST60 or ST80 Navigator Keypad on page 3-15) to name the route. Press ENTER to finish and clear the Name List, or press CLEAR to cancel the operation. To return to the default soft key display, press ENTER again. Clearing the Current Route You can clear the current route from the screen. When you select CLEAR ROUTE if the current route has not been saved, you have the option of saving it and, if you are following the current route, you have the option to stop. If you are following the current route the STOP FOLLOW soft keys are displayed. If the route has not been saved the SAVE ROUTE soft keys are displayed. To clear the route, without saving it in the route database, press NO. The Name route soft keys are displayed and you should continue as described in the previous section, Saving the Current Route on page 3-22. [. . . ] The Installed Warranty provides for onboard repair or exchange, by Raymarine or it's approved service agents, for a period of 2 years/24 months, from date of sale of the boat to the end user ­ where the equipment has been installed by a Raymarine certified installer, or from commissioning of the installation by a Raymarine certified installer, or 30 months from date of shipment of the equipment from Raymarine ­ whichever expires first, except as provided below. Obtaining Warranty Service In the event of Warranty service being required, contact Raymarine or the nearest Raymarine certified service agent ­ a full list of local service agents are available on the Internet or can be requested from the nearest Raymarine agent. A suitable proof of purchase, showing date, place of purchase, and serial number must be made available to Raymarine or authorized service agent at the time of request for Warranty service. In cases where a Raymarine certified installer has not installed the product; i. e. Limited Warranty, the affected unit must be returned to the local Raymarine approved service agent, with a copy of proof of purchase and/or completed warranty card. [. . . ]