User manual RAYMARINE ST30 SPEED

[. . . ] 7 1. 5 Connection to adjacent ST30 instruments . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 2: Transducer Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. 1 Connection to instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. 2 Transducer type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 26 Return to normal display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Chapter 7: General Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 4 ST30 Speed Operation and Installation Handbook Introduction Designed for above or below deck installation, the ST30 Speed can be used as a stand-alone master instrument or can be set to repeat speed information from the SeaTalk bus. The ST30 Speed will display the following information: Boat speed Log Trip Maximum speed Average speed Illumination level ots Kn TR TO MA XI IP L TA M MU E AV RA GE SP DI Y LA SP EE D TM D582 Chapter 1: Control Head Installation 5 Chapter 1: Control Head Installation 110mm (4. 33in) 42mm (1. 65in) 24mm (1. 0in) TOTAL MAXIMUM AVERAGE DISPLAY Autohelm SPEED D583 1. 1 Siting The ST30 Speed may be installed above or below deck where it is: easily readable by the helmsman (normally viewed at eye level) protected from physical damage at least 230mm (9in) from a compass at least 500mm (20in) from radio receiving equipment accessible from behind for ease of installation and cable running Note: To prevent the build-up of moisture the instrument breathes through the back cover. For this reason the instrument must be mounted where the back cover is protected from direct water. The rear case is fitted with a foam gasket to form a water-tight seal between the instrument and the installation face. 56mm (2. 20in) 88mm (3. 46in) TRIP 6 ST30 Speed Operation and Installation Handbook 1. 2 Mounting procedure 3 5 6 2 4 1 D584 1 Instrument 2 Fixing studs 3 Thumb nuts 4 Sealing gasket 5 Power supply cable 6 Transducer cable 1. 2. Make sure the surface to which the instrument (1) is to be mounted is smooth and flat. Use the template (supplied) to mark the centres for the two fixing holes and the instrument connector boss. Note: To allow protective covers to be fitted, adjacent instruments should be sited not less than 6mm (0. 24in) from each other (116mm centre to centre min. ). 3. Using a 60mm (2 3/8in) diameter cutter, drill a location hole for the instrument connector boss. Connect the power supply and transducer cables to the back of the instrument (1) (see relevant installation sections). Install the instrument (1) in the chosen location and secure with the thumb nuts (3) provided. Chapter 1: Control Head Installation 7 1. 3 Power supply (Stand-alone operation) Caution: The ST30 Speed must only be connected to a 12V supply. + + SEATALK + + 12V Supply Red Screen D585 For stand-alone operation, use the 1 metre cable supplied with the instrument. Connect the moulded power supply plug to either SeaTalk connection on the rear of the instrument and run the free end back to the vessels distribution panel. Cut the power cable to length and connect the red wire to the positive 12V terminal and the screen to 0V. Protect with a 5A circuit breaker or fuse. 2. 1. 4 Power supply (SeaTalk operation) If the ST30 Speed is to be connected to an existing SeaTalk system use a Standard SeaTalk Extension or Interface cable. Autohelm Power Extension Cable D628 SP D EE + 5A Autohelm Autohelm 8 ST30 Speed Operation and Installation Handbook 1. 5 Connection to adjacent ST30 instruments The ST30 Speed is supplied with a daisy-chain cable that allows adjacent ST30 instruments to be linked together. The daisy-chain cable supplies power to adjacent instruments and allows data to be transmitted and received via the SeaTalk bus. The daisy-chain cable plugs into one of the SeaTalk ports on the back cover. Chapter 2: Transducer Installation 9 Chapter 2: Transducer Installation 2. 1 Connection to instrument The transducer is supplied with 10m (32. 5ft) of cable that plugs directly into the back of the instrument. + + SEATALK + SP D EE + D586 10 ST30 Speed Operation and Installation Handbook 2. 2 Transducer type The ST30 Speed system is supplied, as standard, with a plastic through hull transducer. This is suitable for use with Glass Reinforced Plastic (GRP), Steel and Aluminium hulls at speeds up to 32 knots. Wooden hull and transom mount installations require a different type of transducer. Please refer to the following table for details. Hull material or Boat speed (max) Transducer type location GRP, Steel, Aluminium GRP, Steel, Aluminium Wood Transom 32kts 45kts Standard through hull Standard with high speed paddle Bronze (Z116) Transom mount with bracket (Z119) 45kts 60kts Caution: Plastic through hull transducers must not be used on vessel's with wooden hulls. Note: The ST30 speed transducers are fitted with standard paddlewheels designed for speed up to 32 knots. For vessel's that will exceed this speed, please refer to section 2. 3 which contains instructions on how to fit the high speed paddlewheel (supplied). 2. 3 Paddlewheel replacement If the high speed paddlewheel (supplied) is to be fitted, or the existing paddlewheel to be replaced, proceed as follows: 1. Remove the retaining rings (1) and pin (6) from the speed transducer (3). If replacing a worn paddlewheel and if the vessel is still in the water, replace the speed transducer (3) with the plug (5). Remove the pin (6) that retains the paddlewheel (7) in the speed transducer (3). [. . . ] Press and hold Diiplay and *for 14 seconds until CAL is displayed forthe second time. Chapter 6: Calibralion 25 2. Momentarily press A and V together. CO = Calibrtion locked, i. e. Mode selection is altered using A key. Return to normal display Press and hold Display and *. After 2 seconds the display returns to `Speed' mode. 26 ST30 Speed Operation and Installation Handbook 6. 3 Master/Repeater display As it leaves the factory, the ST30 Speed is set to operate in Master mode. In this mode the instrument is connected to a speed transducer and transmits speed information onto the 'SeaTalk' bus. [. . . ]