User manual RCA F35100ST

[. . . ] Color TV Owner's Manual First-Time Operation OF ON F VC CA R1 VC R2 BL E AU 1 DIO TV 2 CH AN pp. 2-3 Complete Operator's Guide and Reference Manual Monitor Panel and Detailed Connections Trouble Checks 3 4 NE L 5 6 7 8 VO 9 INP ME UT CS NU 0 PC LU ME ­ + ID CL EA RD MU AN TE T PR OG PL RE pp. 4-25 AY PA US E ISP LA Y WIN D FF ST RE AP SR PIP OF ZO OM OU F SW OP CO RD T CH GU S( AN FR · ) Z IDE pp. 49 Introduction Thank you for choosing RCA Congratulations on your purchase of an RCA TV. [. . . ] · Refer to pages 34-35 if you want to review details about connecting your VCR to your TV. 22 Setting Up Cable Box Channel The CABLE CHAN function lets you program to which channel the TV will automatically tune when you press the CABLE button on the remote. You will no longer have to remember the output channel of the cable box because the TV will remember for you. For example, if you connect a cable box to the TV's CABLE/ANTENNA connector (as shown on page 30 or 31), you will no longer have to remember to select channel 2, 3, or 4 on the TV to see what's coming from the cable box. By entering the cable box's output channel (usually 02, 03, or 04) next to the CABLE CHAN function, the TV will automatically tune to that channel each time you press the CABLE button on the remote. This function is especially convenient if you have a remote-controllable cable box that can be operated by the CABLE button on the remote (as described on page 32). Pressing the CABLE button will then not only switch the remote to cable mode but will also automatically tune the TV to the proper channel for viewing the picture from the cable box. Note: Pressing the CABLE button does not change between ANT A and ANT B antenna inputs as explained on page 15. Setting Up Cable Box Channel (with or without remote) 1. Repeatedly press MENU to select the SETUP MENU, and then press + or ­ to display the setup functions. Press the + button to program the channel number you selected into the CABLE CHAN function memory. 8:27PM 03 8:27PM MUTE VIDEO MENU AUDIO MENU SETUP MENU 13 CHAN MEM: STORED CABLE/AIR: CABLE VCR 1 CHAN: 91 VCR 2 CHAN: 92 CABLE CHAN: 03 CHAN MEM: STORED CABLE/AIR: CABLE VCR 1 CHAN: 91 VCR 2 CHAN: 92 CABLE CHAN: OFF Note: Pressing the ­ button here will turn off this feature and display CABLE CHAN: OFF again. 2. Enter the channel number you want to program by pressing two digit buttons on the remote control. (The channel number you enter is the channel to which the TV will tune automatically when you later press the CABLE button on the remote. ) The TV will change to the channel you select. This will help you to confirm that it is indeed the channel you want the TV to automatically tune. Most cable boxes output their signals on either channel 02, 03, or 04. 8:27PM 03 CHAN MEM: STORED CABLE/AIR: CABLE VCR 1 CHAN: 91 VCR 2 CHAN: 92 CABLE CHAN: OFF 23 Picture-in-Picture (PIP) After you have connected another video source (such as a VCR or camcorder) to INPUTS 1 or INPUTS 2 on your TV (as shown on pages 34, 35, or 38), you are ready to display picture-in-picture. Changing Channels (PIP) To change channels on the picture from the TV, press the TV button on the remote, and then press either the CHANNEL up or down button or two number buttons. Picture from TV Starting Picture-in-Picture (PIP) 1. (This step can be skipped if the remote is already in the "TV mode". ) 3. The little picture and the big picture will be the same. To change channels on the picture coming from the VCR, press VCR1 or VCR2 (if you've programmed the VCR1 or VCR2 button to control the VCR as described on page 37) and then press either the CHANNEL up or down button or two number buttons. You can also change the VCR's picture by pressing the CHANNEL buttons on the front of the VCR. 4. To get a picture from the other source (VCR, camcorder, etc. ), first turn on the other source, and then select TV channel 90, 91, or 92 (explained below). The picture from the other source will appear in the little picture. Picture from TV Picture from VCR The small picture can be moved, enlarged, reduced, frozen, or switched with the main picture as desired. Details are on the next page. Picture from VCR · If the other source is connected to the TV's INPUT 1 jacks, select TV channel 91 to see the signal. If you have programmed the VCR1 or VCR2 button to automatically select channel 91 as described on page 22, press VCR1 or VCR2. · Select channel 92 if the other source is connected to the TV's INPUT 2 jacks. If you have programmed the VCR1 or VCR2 button to automatically select channel 92 as described on page 22, press VCR1 or VCR2. · Select channel 90 if the other source is connected to the TV's S-VIDEO connector. [. . . ] Total Amount Enclosed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use VISA or MasterCard preferably. No COD or CASH. $ $ 5. 00 All accessories are subject to availability. Where applicable, we will ship a superseding model. Note: All specifications and descriptions of accessories are subject to change without notice. Please complete other side also 47 Accessory Order Form (continued) Charge your order on your VISA or MasterCard by filling in below To order accessories, contact your local dealer. If a dealer is not nearby, you can also follow the directions below to order by telephone or direct-by-mail. USE YOUR CREDIT CARD ® United States Orders To place your order by phone, have your Visa or MasterCard ready and call the toll-free number listed below between 8AM and 8PM Eastern Standard Time. [. . . ]