User manual RCA RT2380BK

[. . . ] B_RT2380 EN 4/7/04 1:44 PM Page 2 IMPORTADOR Comercializadora Thomson de México, S. A. Telefono: 52-55-11-020360 RFC: CTM-980723-KS5 EXPORTER Thomson Inc. Trademark(s) ® Registered Marca(s) Registrada(s) Marque(s) Deposée 5585891B (EN/F/E) www. rca. com Printed in China / Impreso en China B_RT2380 EN 4/7/04 1:44 PM Page 3 user manual RT2380 RT2380BK It is important to read this instruction book prior to using your new product for the first time. Es importante leer este manual antes de usar por vez primera su euipo. B_RT2380 EN 4/7/04 1:44 PM Page 4 FCC Information This device complies with Part 15 of the FCC Rules. [. . . ] Refer to the "Connecting To Audio-Visual Components" section for details on connection. By default, the VOL+/VOL- and MUTE buttons will only control the receiver, regardless which mode (TV, VCR, etc) the receiver is in. By programming the volume punchthrough function, you can also control the volume of the TV. NOTE Controlling the TV volume can be done in any non-Tuner modes. To activate the volume punchthrough function, follow the procedures below: 1. While holding down the VOL- button, press one of the source buttons to select the source where you want to control TV volume at. You should now be able to control TV volume and mute at the selected device. Using the Remote to Control Additional Components You can use your remote to control most of RCA branded VCRs, satellites, cable boxes or TVs. Press the corresponding source button on the remote control to operate options on other components. HINT To return to controlling receiver volume and mute again, follow the steps above but press TUNER instead of TV in step 3. HINT If batteries are removed from the battery compartment of the remote control, the volume and mute control in all source modes will be the receiver volume and mute conrol except in TV mode. 14 B_RT2380 EN 4/7/04 1:44 PM Page 19 Operating your Receiver Using the receiver to play a source After having properly connected a source (DVD, CD, VCR) to the receiver, you can partly control them through the receiver. Set the sound Mode if needed (see "Advanced sound control" for details). Example 1: To play Dolby Prologic II Movie sound Press the SURROUND buttons until "Dolby PL II MOVIE" appears on the Display and all of the speaker'' icons light up. Example 2: LD: You may need to select a different Audio Channel on your LD (refer to your LD player manual). Adjust the volume knob accordingly. EN Playing a DVD with the receiver 1. Connect a DVD player to the receiver (see connecting your receiver for details). NOTE To play Dolby Digital sound, the source must be connected to the receiver via the optical or coaxial terminal 2. Press ON/STANDBY on the main unit or press ON·OFF on the remote control to switch on the receiver. Press the SOURCE buttons on the main unit or DVD·6 CH on the remote control to select the DVD source. Select the appropriate A/V channel on the TV (refer to your TV manual for details) until the image from the DVD player is displayed. NOTE To receive VCR signal for recording, you must connect analog output from DVD/CD/SAT/TV to the analog input of the receiver. 15 B_RT2380 EN 4/7/04 1:44 PM Page 20 Operating your Receiver Operating the Radio The receiver has a built-in tuner that allows for AM/FM radio function. Automatic Tuning Press and hold TUNER - or TUNER + for about one second to activate the automatic SEARCH function. The receiver will automatically tune frequencies until it finds a station. Manual tuning 1. Connect the FM and AM antenna accordingly (see "Connecting the Antenna" on page 5 section for details) 2. Press ON/STANDBY on the main unit or ON·OFF on the remote control to switch on the receiver. NOTE 1. If there is interference, move the location of the antenna until the optimal sound is heard. TV and other electronic devices could be the cause of interferences so try to position the antenna away from them. Adjust the antenna for better reception and for a more efficient search. 3. Press the SOURCE buttons on the main unit until the tuner mode is selected or press TUNER on the remote control. Select a sound effect if needed by pressing the SURROUND button. To select between FM and AM band, press the TUNER button repeatedly. Selecting Mono or Stereo Sound Press the ST·MONO button on the remote control to toggle between mono and stereo sound in FM tuner mode (when available). 5. Tune to a station by pressing TUNER - or TUNER + repeatedly until the desired station is found. 16 B_RT2380 EN 4/7/04 1:44 PM Page 21 Operating your Receiver Storing radio stations The receiver can store up to 40 radio stations in memory. [. . . ] For rental firms, proof of first rental is also required. How State Law relates to warranty: · Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. · This warranty gives you specific legal rights, and you also may have other rights that vary from state to state. What your warranty does not cover: · Customer instruction. (Your Owner's Manual describes how to install, adjust, and operate your unit. Any additional information should be obtained from your dealer. ) · Installation and related adjustments. [. . . ]