Detailed instructions for use are in the User's Guide.
[. . . ] In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled. [. . . ] Such objects can discolor or otherwise harmfully affect the finish.
357
· To avoid disturbing your neighbors, try to keep the unit's volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night).
558d
· Do not put anything that contains water (e. g. , flower vases) on the piano. Also, avoid the use of insecticides, perfumes, alcohol, nail polish, spray cans, etc. , near the unit. Swiftly wipe away any liquid that spills on the unit using a dry, soft cloth.
· This instrument is designed to minimize the extraneous sounds produced when it's played. However, since sound vibrations can be transmitted through floors and walls to a greater degree than expected, take care not to allow these sounds to become a nuisance to neighbors, especially when performing at night and when using headphones.
Maintenance
401a
· For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth.
402
· Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.
3
Check the Contents of the Box
TD-6 (Percussion Sound Module) x 1 KD-7 (Kick Trigger Unit) x 1 FD-6 (Hi-Hat Control Pedal) x 1 PD-6 (Pad) x 5 CY-6 (Cymbal Pad) x 2 Accessory Set x 1
Tuning Key x 1 Beater (for KD-7) x 1 Anchor Bolt (for FD-6) x 2
TD-6
(Percussion Sound Module)
Attach the stand holder (included with the drum stand MDS-6) to the TD-6.
Narrow
Wide
Spring for Anchor Bolt (for FD-6) x 2 Wing Nut (for CY-6) x 2 Felt Washer (for CY-6) x 2 Stopper (for CY-6) x 2 Monaural Connection Cable (1 meter) x 3 (for Hi-Hat, Snare, Tom1: PD-6 x 3) Monaural Connection Cable (2 meters) x 4 (for Kick: KD-7/Tom2, 3: PD-6 x 2/ Hi-Hat Control Pedal: FD-6) Stereo Connection Cable (2 meters) x 2 (for Crash, Ride: CY-6 x 2) · To attach the stand holder, remove the four 8 mm screws (M5 x 8) from the bottom of the TD-6 and use them. · When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to orient the unit so no buttons or controls get damaged. · When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over.
TD-6K Owner's Manual x 1
KD-7
(Kick Trigger Unit)
Pad Face
· This package does not include a kick pedal. · The TD-6 Owner's Manual is included in the TD-6 package.
Anchor Bolt
In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
Foot Plate
Output Jack Mix In Jack
MDS-6
(Drum Stand)
Low
High Output Level Control Polarity Switch
Assemble the Drum Stand.
About the Stand (MDS-6), refer to the owner's manual for the stand.
Setting the Polarity Switch
Move the polarity switch to the "(-Roland)" position.
4
Using the Mix In Jack
You can obtain twin pedal performance if you connect the output from a second KD-7 to the Mix In jack on the first KD-7.
FD-6
(Hi-Hat Control Pedal)
Adjusting the Travel of the Pedal
Adjusting the Output Level Control
When the level of a second KD-7 that's been connected to the Mix In jack does not match that of its partner, you can finely adjust the output with the output level control. When only one KD-7 is being used, the output level control should normally be turned to its maximum setting.
Shift the Arm
deep
shallow
Loosen the nut with the included tuning key. After adjusting, tighten the nut.
Installing the Beater and a Commercially Available Kick Pedal
This package does not include a kick pedal. Use with a commercially available kick pedal.
Beater
Pedal Plate
Control Out Jack Commercially Available Kick Pedal
Attaching the Anchor Bolts (When Using on the Carpet)
Anchor Bolt
Adjusting the Anchor Bolts
Spring for the Anchor Bolt
When Using on the Carpet
When Using on the Floor
· Take care not to pinch your fingers. · When used on flooring, the anchor bolts may damage the floor. · Install the kick pedal securely.
Specifications
KD-7: Kick Trigger Unit Trigger: 1 Dimensions: 172 (W) x 112 (D) x 100 (H) mm 6-13/16 (W) x 4-7/16 (D) x 3-15/16 (H) inches Weight: 1. 3 kg / 2 lbs 14 oz (including beater)
· The tips of the anchor bolts are sharp. · When using on flooring, the anchor bolts may damage the floor. · When the FD-6 is not going to be used for a long period of time, move and fix the arm, allowing longer travel for the pedal. · To avoid damage, do not leave the FD-6 for extended periods of time with the pedal plate depressed.
The TD-6 owner's manual assumes use of the FD-7 Hi-Hat Control Pedal. For each instance in which you find "FD-7" mentioned in the TD-6 owner's manual, please substitute the name "FD-6. "
Specifications
FD-6: Hi-Hat Control Pedal Dimensions: 160 (W) x 395 (D) x 120 (H) mm 6-5/16 (W) x 15-9/16 (D) x 4-3/4 (H) inches Weight: 1. 4 kg / 3 lbs 2 oz (including anchor bolts)
5
PD-6
(Pad)
Stand Fixing Screw Holder
CY-6
(Cymbal Pad)
Bow Portion Head Edge Portion Pad Face
Stand Fixing Screw Holder Output Jack Output Jack
Attaching the CY-6 to a Cymbal Mount Attaching the PD-6 to a Stand
Pass the rod through the pipe that is inside the holder.
Tighten
1. Use the included tuning key to tighten the stopper bolt.
The stopper keeps the cymbal pad from turning, and prevents the cables from catching or getting tangled on the stand.
Loosen
Tighten the bolt with the included tuning key.
Stopper (Be sure to orient it correctly)
Rod
When attaching the PD-6s to the mounts, be sure to tighten the stand fixing screws securely. Kontor Norge
Lilleakerveien 2 Postboks 95 Lilleaker N-0216 Oslo NORWAY TEL: 2273 0074
JORDAN
AMMAN Trading Agency
245 Prince Mohammad St. , Amman 1118, JORDAN TEL: (06) 464-1200
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429
TAIWAN
ROLAND TAIWAN ENTERPRISE CO. , LTD.
Room 5, 9fl. [. . . ] C. , V6V 2M4 CANADA TEL: (604) 270 6626
INDONESIA
PT Citra IntiRama
J1. 15J-150 Jakarta Pusat INDONESIA TEL: (021) 6324170
COSTA RICA
JUAN Bansbach Instrumentos Musicales
Ave. 1. Calle 11, Apartado 10237, San Jose, COSTA RICA TEL: 258-0211
GREECE
STOLLAS S. A. Music Sound Light
155, New National Road Patras 26442, GREECE TEL: 2610 435400
KOREA
Cosmos Corporation
1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855
MIDDLE EAST
BAHRAIN
Moon Stores
No. 16, Bab Al Bahrain Avenue, P. O. Box 247, Manama 304, State of BAHRAIN TEL: 211 005
CHILE
Comercial Fancy S. A.
Rut. : 96. 919. 420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540
Roland Canada Music Ltd. [. . . ]