Detailed instructions for use are in the User's Guide.
[. . . ] TD-6KW
Owner's Manual
Thank you, and congratulations on your choice of the Roland Drum System TD-6KW.
201a
Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.
* For the Snare (PDX-8) to function correctly, trigger parameters in the sound module TD-6V must be adjusted.
202
Copyright © 2006 ROLAND CORPORATION All rights reserved. [. . . ] Attach the CY-8 so the Roland logo is positioned on the opposite side of the playing area. Tighten the wing nut to obtain the desired movement.
Use the included felt washer and the wing nut.
fig. CY-Set02. e
Wing Nut Felt Washer
Specifications
CY-8 Size: Triggers: Dimensions: Weight: Accessories: 12 inches 2 (Bow, Edge) 290 (W) x 295 (D) x 47 (H) mm 11-7/16 (W) x 11-5/8 (D) x 1-7/8 (H) inches 650 g / 1 lb 7 oz Wing Nut, Felt Washer, Stopper
Double sounding may occur if the wing nut is loose.
* Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad's function.
10
USING THE UNIT SAFELY
FD-8
fig. FD-8. e
(Hi-Hat Control Pedal)
Using the FD-8
Using the FD-8, you can control the opening and closing of the hi-hat sound.
Adjusting the Travel of the Pedal
Loosen the nut with a tuning key. deep Shift the Arm
Open Hi-Hat
Strike the hi-hat without pressing the pedal
Half Open Hi-Hat
shallow
Strike the hi-hat with the pedal pressed half-way
Closed Hi-Hat
Pedal Plate Anchor Bolt
Strike the hi-hat with the pedal pressed
Foot Closed
Completely press down the pedal
Control Out Jack
Foot Open
Press the pedal and then immediately release it Attaching the Anchor Bolts (When Using on the Carpet)
Anchor Bolt Spring for the Anchor Bolt
The volume of the Foot Closed sound can be adjusted separately (TD-6V Owner's Manual; p. · When using on flooring, the anchor bolts may damage the floor. · When the FD-8 is not going to be used for a long period of time, move and fix the arm, allowing longer travel for the pedal. · To avoid damage, do not leave the FD-8 for extended periods of time with the pedal plate depressed.
· Connect the FD-8 to the TD-6V before turning on the power. · Do NOT press the pedal when turning on the power.
Specifications
FD-8 Dimensions: Weight: Accessory: 130 (W) x 396 (D) x 103 (H) mm 5-1/8 (W) x 15-5/8 (D) x 4-1/16 (H) inches 1. 3 kg 2 lbs 14 oz Tuning Key
11
USING THE UNIT SAFELY
KD-8
fig. KD-8. e
(Kick)
Output Jack
3. Use a tuning key to tighten the screws removed in Step 1 so that the stand is firmly secured.
fig. KD-Assy03
Head
Stand
Anchor Bolt
4. Attach the kick pedal.
Foot Plate
Position the beater so that it strikes the center of the head, then secure the kick pedal and KD-8 firmly in place.
fig. KD-Assy04. e
Making the Settings
1. Remove the screws attached to the reverse side of the KD-8's trigger.
fig. KD-Assy01
Beater
Install the kick pedal securely.
Adjusting the Foot Plate Height
Depending on your kick pedal, it can be unstable when you attach it to the KD-8. Be sure to adjust the foot plate height so that the entire bottom surface of the pedal is attached to the floor.
fig. KD-Assy05. e
2. Pull out the stand in the direction indicated by the arrow until it is fully extended.
fig. KD-Assy02
Beater
Commercially Available Kick Pedal
* Adjust the height so that the entire pedal comes into contact with the floor.
12
1. Loosen the stand's anchor bolts and remove the foot plate.
fig. KD-Assy06
Adjusting the Anchor Bolts UNIT SAFELY USING THE
When using the kick pedal on a carpet or similar surface, adjust the anchor bolts so their tips protrude from the plate and secure the pedal in place; this will make it easier to use the kick pedal. However, when used on flooring, the anchor bolts may damage the floor. Adjust the anchor bolts correctly.
fig. KD-Anchor. e
Adjusting the Anchor Bolts
When Using on the Carpet
When using on the Floor
The tips of the anchor bolts are sharp. Set the kick pedal so that the entire bottom surface is attached to the floor. Tighten the anchor bolts securely there to fix the stand and foot plate.
fig. KD-Assy07. e
When Using a Twin Pedal
fig. KD-Pedal1
Position the two beaters equally apart from the center of the pad as shown in the figure at left. If one of the beater is further away from the center than the other, the sound from the further beater will be lower in volume, or will not sound as desired.
fig. KD-Pedal2
This hight will vary depending on your kick pedal.
Using a twin pedal will result in lower sensitivity as compared to when a single pedal is used. Raise the sensitivity on the sound module.
· Install the kick pedal securely. · When moving the setup, be sure to remove the screws and fold the stand. Transporting the KD-8 while it remains open may subject the stand to excessive strain and result in damage to the stand.
Specifications
KD-8 Dimensions: Weight: Accessories: 272 (W) x 260 (D) x 405 (H) mm 10-3/4 (W) x 10-1/4 (D) x 16 (H) inches 2. 9 kg 6 lbs 7 oz Screws
* Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad's function.
13
. USING THE UNIT SAFELY
Assemble the "TD-6KW"
921
Using the provided cables, connect the pads. [. . . ] Service Division 22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: 2415 0911 Parsons Music Ltd. 8th Floor, Railway Plaza, 39 Chatham Road South, T. S. T, Kowloon, HONG KONG TEL: 2333 1863
CENTRAL/LATIN AMERICA
ARGENTINA
Instrumentos Musicales S. A. Av. Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700
DENMARK
Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200
SWITZERLAND
Roland (Switzerland) AG Landstrasse 5, Postfach, CH-4452 Itingen, SWITZERLAND TEL: (061) 927-8383
MEXICO
Casa Veerkamp, s. a. No. 37 Beyoglu - Istanbul / TURKEY TEL: (0212) 249 85 10
FINLAND
Roland Scandinavia As, Filial Finland Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)9 68 24 020
BARBADOS
A&B Music Supplies LTD 12 Webster Industrial Park Wildey, St. Michael, Barbados TEL: (246)430-1100
UKRAINE
EURHYTHMICS Ltd. [. . . ]