User manual ROLLS MP128

[. . . ] We supply this note for those adventurous people who may want to give it a try. Connect pin 1 to circuit ground, and pin 3 to +9 - +15 VDC of the receiving unit. This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser's receipt. [. . . ] This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RFX Salt Lake City, UT 8/99 LIMITED WARRANTY MIDI CONTROLLER MIDIBUDDY MP128 SPECIFICATIONS Size: Weight: Power: Phantom Power: Display: Output: Output Jacks: Chassis: 17" X 5" X 1. 5" (381 x 127 x 38 mm) 3 lbs. 2 digit red, . 56" high efficiency Standard MIDI Program Change, Song Start/Stop 2 DIN jacks (MIDI OUT, MIDI SHARE) Black painted steel OWNERS MANUAL INTRODUCTION Thank you for purchasing the RFX MP128 MIDIBUDDY. The MP128 sends standard MIDI program changes to select patches on a MIDI keyboard, digital signal processor, or other MIDI controllable device. MIDI data is sent only when a 1 - 9 button is selected except as described below. The display will show a "-" in the right hand digit when no MIDI information is sent, or when a 10's UP or DOWN button is pressed. For example; to send program 47, press the 10s UP or 10s DOWN until the display reads "4-" then press the 7 button. When the 7 button is pressed, program 47 is sent out and the number is displayed by the LED readout. MIDI Start and Stop Commands When program "00" is selected, the MP128 display shows an "ST" (which looks more like an Sr), and sends a MIDI start command. When program "129" is selected, an "SP" is displayed and a MIDI Stop command is sent. A. Program/Function Display Window C: 127/128 (Dip switch #6) Switch D: PROGRAM CHANGE/SONG SELECT (DIP switch # 5) Switch E: MIDI CHANNEL SELECT Switches (DIP switches 4, 3, 2, and 1) F: SHARE output G: MIDI output jack H: POWER jack INSTALLATION · Apply power (Rolls Model PS27, 12VDC, 150mA) to the Power jack on the rear of the MP128. The MP128 may also be "phantom-powered" which means powering the unit via unused pins of the MIDI cable. · Connect the MIDI OUT of the MP128 using a standard MIDI cable, to the MIDI IN on the device to be controlled. The MIDIBUDDY may be used on the floor and foot switched or placed on top of a keyboard for easy hand access. The unit, with slight modification, will fit in a standard 19 inch audio rack if necessary. · The "SHARE" jack is in parallel with the OUT jack and operates as a MIDI "Thru" for connecting several devices together. [. . . ] If all switches are in the off position, MIDI channel 1 is selected, if all are on, MIDI channel 16 is selected. CH# ON OFF CH# ON OFF 1 1, 2, 3, 4 9 4 1, 2, 3 2 1 2, 3, 4 10 1, 4 2, 3 3 2 1, 3, 4 11 2, 4 1, 3 4 1, 2 3, 4 12 1, 2, 4 3 5 3 1, 2, 4 13 3, 4 1, 2 6 1, 3 2, 4 14 1, 3, 4 2 7 2, 3 1, 4 15 2, 3, 4 1 8 1, 2, 3 4 16 1, 2, 3, 4 · Switch #5 selects whether the MP128 transmits Program Change information only, or transmits Program Change and Song Pointer. · Since some MIDI devices display their programs as 0 - 127, and others display 1 - 128, the MIDIBUDDY's DIP switch #6 will select either of these two. [. . . ]