User manual ROLLS MX902

[. . . ] Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Channel Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Live Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 2 3 4 5 6 Rear Cover Front Panel CHANNEL DESCRIPTIONS HIGH: Boosts or cuts the 12. 5 kHz or high frequency portion of the signal. AUX 2: Controls the amount of post-fader signal that is sent to the Aux 2 bus and output. AUX 1: Controls the amount of pre-fader signal that is sent to the Aux 1 bus and output. PAN: Varies the amount of relative signal sent from Channels' 1 through 3 to the Main Level control. BAL: Varies the amount of stereo signal from channels 5/6 through 8/9 to the Main Level control. LEVEL: Controls the overall output signal level of the channel. -OO LEVEL +15 -OO LEVEL +15 -15 12. 5 k +15 HIGH -15 12. 5 k +15 HIGH -15 60 +15 LOW -15 60 +15 LOW 0 AUX 2 10 0 AUX 2 10 0 AUX 1 10 0 AUX 1 10 L PAN R L BAL R 3 4/5 MASTER DESCRIPTIONS AUX 2 RETURN: Controls the amount of input signal from the RCA Aux 2 Return jacks. AUX 1 RETURN: Controls the amount of input signal from the Aux 1 Right and Left Return jacks. HEADPHONE LEVEL: Controls the amount of level of signal from the Headphone Output. HEADPHONE OUTPUT: 1/4" TRS stereo jack for connection to stereo headphones. CLIP L R PWR L 12 - 18 VDC AUX 2 RET + POWER R MX902 0 NOTE: Do not use a mono 1/4" TS plug in this jack. Doing so may result in serious damage to the MX902. 0 AUX 2 10 RETURN AUX 1 10 RETURN HDPHN OUT MAIN LEVEL: Controls the amount of signal sent to the Right/Left output jacks. -OO LEVEL +15 HDPHN -OO LEVEL +15 MAIN 2 Jack Panel Description MIC 1 MIC 2 MIC 3 PHANTOM PWR AUX 1 SEND AUX 2 SEND LEFT OUT RIGHT OUT 4/LEFT/MONO TRIM TRIM TRIM 6/LEFT/MONO 8/LEFT/MONO AUX 1 RET LEFT/MONO +6 dB +50 LINE 1 -6 dB +6 dB +50 LINE 2 -6 dB +6 dB +50 LINE 3 -6 dB 5/RIGHT 7/RIGHT 9/RIGHT AUX 1 RET RIGHT Channels 1 through 3 MIC INPUT: XLR input jack for microphone level or balanced signals. LINE: 1/4" unbalanced input for instrument of line level signals. PHANTOM POWER SWITCH: Engages the +24 volts of phantom power, used to power condenser microphones. Channels 4/5 through 8/9 LEFT: 1/4" unbalanced input for instrument or line level signals. RIGHT: 1/4" unbalanced input for instrument or line level signals. Master AUX 1 and 2 SEND: 1/4" unbalanced jacks for sending out the signals present on the Aux 1 and 2 buses. RIGHT and LEFT: 1/4" unbalanced jacks for receiving stereo signals sent from the Aux 1 bus (usually through an effects processor). Stereo RCA jacks for receiving stereo signals send from the Aux 2 bus, or may be used as an auxiliary stereo source input such as a CD or cassette player. Side Panel 12 - 18 VDC: For connection to a sleeve positive, DC power adapter. POWER Switch: Applies power to the MX902 when connected to a proper power source. 3 MIC 1 MIC 2 MIC 3 PHANTOM PWR AUX 1 SEND AUX 2 SEND LEFT OUT RIGHT OUT 4/LEFT/MONO 6/LEFT/MONO 8/LEFT/MONO AUX 1 RET LEFT/MONO +6 dB +50 LINE 1 -6 dB +6 dB +50 LINE 2 -6 dB +6 dB +50 LINE 3 -6 dB 5/RIGHT 7/RIGHT 9/RIGHT AUX 1 RET RIGHT to Effects Input from Left Output STEREO EFFECTS DEVICE from Right Output SIGNAL PROCESSOR CONNECTION Use Aux 1 Output to connect to the Input of your signal processor which may be an echo unit, a reverb, or multi effects unit. [. . . ] Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt. In the absence of such purchase receipt, the warranty period shall be one (1) year from the date of manufacture. This warranty shall be invalid if the product is damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than our own service facility or an authorized Service Center, or any use violative of instructions furnished by us. This one-year warranty is in lieu of all expressed warranties, obligations or liabilities. [. . . ]