User manual RUSSOUND SMART SELECT VOLUME CONTROL
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND SMART SELECT VOLUME CONTROL. We hope that this RUSSOUND SMART SELECT VOLUME CONTROL user guide will be useful to you.
Manual abstract: user guide RUSSOUND SMART SELECT VOLUME CONTROL
Detailed instructions for use are in the User's Guide.
[. . . ] With a few simple calculations and jumper settings, your SSVC system can be configured to connect up to 16 pairs of speakers to a single amplifier.
Smart SelectTM Volume Control
Instruction Manual
2 SYSTEM IMPEDANCE =
the surface of a metal junction box during installation or removal. The junction box must also have a depth of at least 3 1/8".
5) Since you have determined the system impedance you can now calculate the jumper setting needed to protect your amplifier. IMPEDANCE (step 1) SYSTEM IMPEDANCE (step 4)
4 Ultra-MatchTM CONFIGURATION INSTRUCTIONS
With a few simple calculations, Russound Ultra-MatchTM Volume Controls eliminate the need for a speaker selector. By determining the impedance of the system, the correct jumper settings for the volume controls can be calculated to allow safe operation of your system. [. . . ] 5) Connect the Smart SelectTM Power Interrupter to the EZB-1 connecting block as shown in Figure 2. The +V connection from the Smart SelectTM Power Interrupter should connect to the terminal of the EZB-1 which corresponds to the +12V connection of the SSVC. The GND connection from the Smart Select Power Interrupter should connect to the terminal of the EZB-1 which corresponds to the Gnd1 connection of the SSVCs. 6) To eliminate the risk of damaging one or more components of the Smart SelectTM system, make sure that all connections are correct and that no wires are shorted. 7) Once all connections are made, install the SSVC in the junction box or plaster ring. Taking the time to feed the excess wire out the back of the junction box will help you with the final assembly. If a junction box will be used, Russound recommends you use plastic junction boxes, if possible. This is to help ensure that the volume control does not short against
5 OPERATION INSTRUCTIONS
1) Make sure the amplifier or receiver is turned Off and it's volume set to minimum. 2) Connect 12 Volt power to the Smart SelectTM System (see Figure 2) NOTE: The 12 Volt power supply (Russound part No. 1201A) must be connected through the Russound Smart SelectTM Power Interrupter Module (Figure 2). 3) The status indicator light should be illuminated red on all volume controls connected. This means that the volume control is currently in Mute mode, and that the speakers are disabled. The status indicator should now blink 3 times and then turn solid green. This means that the SSVC is now in Active mode, and that the speakers are enabled. 7) Turn On the amplifier or receiver and select a music source, such as tuner or CD player. 8) Slowly turn up the amplifier or receiver volume and set it to a comfortable (not maximum) listening level. If the sound becomes muddy or distorted, you have LIMITED WARRANTY
The Russound SSVC is fully guaranteed for Two (2) years from the date of purchase against all defects in materials and workmanship. During this period Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. For this warranty to apply, the unit must be installed and used according to its written instructions. The unit must be returned to Russound at the owner's expense and with prior written permission. Accidental damage and shipping damage are not considered defects under the terms of the warranty. Russound assumes no responsibility for defects resulting from abuse or servicing performed by an agency or person not specifically authorized in writing by Russound. [. . . ] To mute all volume controls (All Off feature) 1) On any SSVC, press the function control button until the status indicator light is red. 2) Press and hold the function control button until the status indicator blinks amber. To enable all volume controls (All On feature) 1) On any SSVC, press the function control button until the status indicator light is solid green. 2) Press and hold the function control button until the status indicator blinks amber. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND SMART SELECT VOLUME CONTROL
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND SMART SELECT VOLUME CONTROL will begin.