User manual RUSSOUND SP622.1
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND SP622.1. We hope that this RUSSOUND SP622.1 user guide will be useful to you.
Manual abstract: user guide RUSSOUND SP622.1
Detailed instructions for use are in the User's Guide.
[. . . ] A/V
DISTRIBUTION
&
CONTROL
SYSTEMS
Instruction Manual
SP652. 1 SP622. 1
INTRODUCTION
Congratulations on selecting Russound Wall-Mounted Speakers. Like all RUSSOUND speakers, they combine acoustic technology with durability and will provide years of musical enjoyment. This manual is designed to make your SP652. 1 & SP622. 1 speakers as easy to install as they are to listen to. If you've had any home "do-ityourself" experience, you should find installation of your new speakers a simple job. [. . . ] Temporarily place a Russound speaker into the cut-out to insure that it fits properly. It's okay if the hole is slightly large, since it will be covered by the speaker's outside frame. Actual installation will happen later, after you've routed the speaker wires. Now it's time to drill the hole on the OTHER end -at the point where the wires from the speakers will exit to the amplifier/receiver. * If you want a custom look, install an outlet box against a stud and cover it with a single outlet plate which has one hole in the middle for the wires to exit from OR order from your Russound dealer a Russound Stereo pair Wall Plate Connector.
Drawing 3
A. Cut speaker hole along outline
6
HOOKING UP YOUR SPEAKERS
IDENTIFYING "+" AND "-" You need to be able to discriminate between the two conductors of the speaker wire. If your wire has transparent insulation, this is easy: One conductor will be copper-colored and the other silver-colored. Generally, professionals denote the copper one as POSITIVE (+) and the silver one as NEGATIVE (-). If you've used wire which has an opaque insulation, there are still differentiating markings. A painted stripe or dotted line * Denote any of these as the POSITIVE (+) conductor for similar connections on both ends. NOTE: It is important that you label your wires left and right when you run them to eliminate future confusion. Cut off excess wire, leaving about 2 feet extending through the speaker cut-out hole. Pull the conductors apart so they're separated for the first two inches from their ends. Using a wire stripper, diagonal pliers or a knife, remove 1/2 inch of insulation from each conductor. Twist the tiny strands in each conductor into tight spirals, as shown in Drawing 4. IMPORTANT: Route the speaker wire THROUGH the sheetrock as shown in Drawing 5. Press down on the protruding levers while inserting the wire into the hole.
* Correct the POSITIVE (+) conductor to the RED terminal and the NEGATIVE (-) conductor to the BLACK speaker terminal. * Make sure that no stray strands of wire have gotten detached and are touching the other main wire. Repeat Steps 1 through 6 for the other Russound In-Wall Speaker.
AT THE AMPLIFIER END 1. Then replace the grille.
A QUICK TROUBLESHOOTING GUIDE
Before returning your Russound In-Wall Speakers for service, it is a good idea to check out these simple remedies first. Wrong speaker output selected; many receivers have an "A" and "B" speaker switch. If using a "speaker selector", room/station not turned on or improperly connected
No sound from one speaker: 1. [. . . ] The kit comes with two brackets, one for the left speaker and another for the right. Once the house/room is completed, you can install the speaker (more on this below). During new installation, keep the following tips in mind: · Use a small level to verify that the mounting frame is straight. · The flat brackets and nails which attach the speakers are thin enough that they won't interfere with wallboard added later. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND SP622.1
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND SP622.1 will begin.