User manual RUSSOUND ST2-XM2
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RUSSOUND ST2-XM2. We hope that this RUSSOUND ST2-XM2 user guide will be useful to you.
You may also download the following manuals related to this product:
RUSSOUND ST2-XM2 DATASHEET (663 ko)
Manual abstract: user guide RUSSOUND ST2-XM2
Detailed instructions for use are in the User's Guide.
[. . . ] 2
800. 967. 2346
IMPORTANT SAFEGUARDS
11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. 14. Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. [. . . ] C Channel Number (CH NUMBER:) This selection displays the channel number only (e. g. , XM070, XM103). C Channel Name (CH NAME:) This selection displays the channel name only (e. g. , ESPN Radio, Real Jazz). # Channel Number and Name (#:CH NAME:) This selection displays the channel number and name (e. g. , 64:The Groove, 121:Fox News). ST2-XM
Display Preference Mode Next Display Preference Previous Display Preference
OK
ST2-RC
ST2-KP
UNO-S2
UNO-S1
UNO-LRC1
MEM
TUNE
MEM
MEM
TUNE
MEM
17
ST2-XM2 OPERATION
FRONT PANEL CONTROLS
Front Panel Operation
Turning the unit on
To turn the unit on, push the On/Off button up on the front panel. Push the desired memory preset (M1 through M6) button for more than 2 seconds. When the memory preset is saved, the appropriate preset number (M1 through M6) and SAVED appears on the LCD. The selected station setting reappears and the sound resumes after the button is released.
Selecting the desired tuner
From the front panel, use to toggle between the XM tuners. A backlight shows behind the selected label XM1 (green) or XM2 (amber) to indicate the active tuner. In addition, the LCD panel is also backlit green for Tuner 1 and amber for Tuner 2. Each time a tuner is selected the display will refresh with the current station or preset, and all subsequent memory preset entries will be associated with that selected tuner.
Recalling a Memory Preset
To recall a memory preset, use to select the desired bank, then press the desired preset button (M1 to M6). In addition to direct selection, the memory presets can be accessed by using and scroll through all presets for the bank selected. to
Backup and Restore
Once all of the tuner settings are completed, it may be advisable to create a backup of the programmed settings for future use. The backup will then be available in case tuner settings need to be restored. The "RNET Backup Utility" is available through the Document Center at www. russound. com. Also required are a DB9 male-to-female cable and laptop or desktop PC.
Selecting an XM mode
Push to select an XM operating mode.
Exiting an XM mode
Push to exit the XM mode selection menu.
Signal Strength mode
Press and hold and release. To exit press
Selecting the desired channel
Press and release and for manual tuning.
Bank/Memory Presets
Each tuner has six banks of preset memory settings, and each bank holds six presets for a total of 36 possible presets for each tuner (72 total presets). Presets are associated with the tuner that is selected at the time the preset is saved.
Memory Preset programming
From the front panel, perform these steps: 1. Tune to the desired channel.
18
ST2-XM2 OPERATION
ST2-RC REMOTE CONTROL
ST2-RC Remote Control Operation
The ST2-RC remote control is the only means of remote operation of the ST2-XM2 in a non--RNET system. The ST2-XM2 front panel displays information for the tuner that is receiving commands from the ST2RC. However, the ST2-RC commands do not change which tuner is playing; that is done through the system's source selection.
number (1 to 6). The memory presets can also be
MEM
accessed by using and presets for the selected bank.
MEM
to scroll through all
Saving Favorites
The remote control stores two "favorites" (similar to memory presets) per tuner. These are set simply by selecting either Tuner 1 or Tuner 2, setting the desired frequency and pressing and holding
FAV 2
FAV 1
Turning the unit on/off
To switch the ST2 tuner in or out of standby mode, push TUNER 2.
PWR
or
or any other button except TUNER 1 or
until "FAV1 (2) saved" appears on the tuner. [. . . ] Press the Setup button three times to back out of the Installation Menu.
To Program the CAM6. 6 (with internal tuner) to operate with the ST2-XM2 Tuner: (refer to the CAM6. 6 Instruction Manual for details)
If the CAM6. 6 has an internal tuner installed in the Source 1 position, use sources 2 through 6 for the ST2-XM2.
Source Configuration Note: When the ST2-XM2 Tuner is used with the CAM6. 6 or other RNET controller, it is configured as an RNET command type "Peripheral" and is connected via the RNET bus. This makes the tuner behave as a fully integrated device with UNO-S1 and UNO-S2 keypad support. Each tuner must be set up with a unique source number (1 - 6) or unassigned. Key Function Note: When using the tuner with the CAM6. 6-S2 system, do not reassign keypad and remote buttons for tuner control in the CAM6. 6 Key Configuration Menu. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RUSSOUND ST2-XM2
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RUSSOUND ST2-XM2 will begin.