User manual SAMMY RANGER MISSION

[. . . ] The limited warranties described above shall be in lieu of any other warranty, expressed or implied, including but not limited to any implied warranty of merchantability or fitness for a particular purpose. 2 HANDLING AND INSTALLATION PLEASE TAKE A MOMENT TO READ THE FOLLOWING BEFORE YOU TURN ON YOUR NEW GAME. The Mighty Driver redemption game is an indoor game machine. Avoid installing the game in the following locations: Locations subject to rain or water damage Locations in direct sunlight Locations subject to extreme heat Locations near hazardous or flammable liquids or chemicals You will need the following minimum dimensions for egress into your location: 60 inches in height 25 inches in width INSTALLATION Unpack your game carefully. The minimum space required for operation in your locations should be: 80" high 30" wide 60" depth THE GAME MUST BE LEVEL. [. . . ] USE A LEVEL TO AVOID NEEDLESS ADJUSTMENTS. SAFETY PRECAUTIONS Be sure to turn the power off or unplug the game before working on the unit. Replace line cord if the insulation is damaged in any way with one of equal quality. Re-check and re-seat all harness connections. 3 GAME PLAY, GA ME SETTING M ODE AND D IPS W SETTING GAME PLAY Insert coin(s) or token(s) . More FLAGS, more tickets. GAME SETTING MODE HOW TO ENTER THE GAME SETTING MODE Re-power on while pressing and holding the RESET Switch which is located inside of front door. Then release the RESET switch OFF to show the ­1 on 2 digits LED display on Marquee box. HOW TO SELECT AND DECIDE EACH CONTENTS After entering GAME SETTING mode, press SERVICE switch to move the number of FUNCTIONS. (2 digits will be changed by pressing the SERVICE switch. ) Press RESET switch to select it. (2 digits will be changed by pressing the SERVICE switch) Press RESET switch to select it. RETURN TO PREVIOUS MENU Change FUNCTIONS and SETTINGS to selection "oo". Select these Digits then press RESET switch to return to previous menu. RETURN TO GAME MODE After selecting any SETTINGS, re-power on the game. For the FUNCTIONS and SETTINGS, please refer to the setting table on next page. Please refer below table. DIP SWITCH 1 FUNCTIONS PAYOUT SETTING SETTING REDEMPTION GAME CARD PAYOUT EXTEND GAME OFF NOTE Ticket payout. When the Left & Right Limit Sensor in the XMECH is activated, Lamp #1 or #9 on the Marquee will light up. Display will show Moving Digits when the Motor is moving. LAMPS ON THE MARQUEE (9 POSITIONS) LED DISPLAY Lamp #1 Lamp #2 Lamp #3 Lamp #4 Lamp #5 Lamp #6 Lamp #7 Lamp #8 Lamp #9 8 BELT MECH. TEST (Press SERVICE switch to select 22, then press RESET switch. ) Spin the Steering Wheel clockwise to move the BELT forward. Lamp #1: Positioning sensor Located Right bottom of BELT from back side view. Lamp #3: Adjusting sensor Located Left bottom of BELT from back side view. Reading the Black and White marks on Right side of Belt. Photo Reflector KR291-AA Part #: 41-60-559 Adjusting Sensor Photo Sensor, KB1240-AA Part #: 41-60-558 BACK VIEW OF CABINET Positioning Sensor Photo Sensor, KB1240-AA Part #: 41-60-558 VENDING DEVICE TEST (Press SERVICE switch to select 23, then press RESET switch. ) Press SERVICE switch to payout Ticket or Card when the setting is Ticket or Card Payout. SOUND TEST Display shows 3­ then press SERVICE switch to go to SOUND TEST. Press RESET switch to count up the number on Display and output the sound. Press SERVICE Switch and Display shows oo, then press SERVICE Switch again to return to previous menu. RETURN TO GAME MODE After TESTING, re-power on the game. 9 ERRORS Display Shows Contents of ERROR Card or Ticket Empty Cause of problem and Solution. Check the Card or Ticket Dispenser. If empty, re-fill the Cards or Tickets and press RESET switch to payout remaining number of Cards or Tickets. [. . . ] If empty, re-fill the Cards or Tickets and press RESET switch to payout remaining number of Cards or Tickets. Check the Card or Ticket Dispenser, clear the jam of Cards or Tickets and re-power on the game. Or exchange the Unit. CE CJ E1 E2 E3 E4 E5 E6 E7 E8 E9 EA Jamming of Card or Ticket Dispenser Coin Switch Error Magnet Error EP-ROM Error Malfunction of X Mech. Malfunction of Belt Unit Card or Ticket Dispenser Error Belt Home positioning or Adjustment Sensor Check the sensor connector, harness and Error wiring. [. . . ]