User manual SCHOLTES B 40 L EC 1 SF

[. . . ] Practical advice on using the burners Before operating your new appliance please read this instruction booklet carefully. However, these rooms must not be communal rooms, bedrooms or rooms which may present a fire hazard. ⷠLiquid petroleum gas sinks to the floor as it is heavier than air. Therefore, rooms containing LPG cylinders must also be equipped with vents to allow gas to escape in the event of a leak. [. . . ] NOTE: if, during the gas conversion procedure, no buttons are pressed for a period of longer than 1 minute, the appliance automatically exits the function without saving the new setting. Once this procedure is complete, replace the old rating sticker with one indicating the new type of gas used. Stickers are available in nozzle kits or can be obtained from any of our Technical Assistance Centres. Setting the burners to minimum (only for gasG20) While the hob is switched off, press the power button T1. Press the buttons T2, T5 and T9 simultaneously and hold them down until the numerical value 01 appears on the display 02; on the displays D3, 4, 5 and 6 a numerical value appears which indicates the set minimum level. Press the + or ­ button corresponding to the burner you are adjusting; the burner will be activated at its maximum level to begin with, and will then be adjusted to the minimum setting value indicated at that moment by the display corresponding to that burner. Use the + or ­ buttons corresponding to the relevant burner to increase or decrease the minimum level; if the minimum level is too low, causing the burner to switch off or operate at such a low level that the thermocouple does not detect the flame, the burner operates at its maximum level for a few seconds and then returns to the minimum level. To save the minimum level setting for the burner, as soon as it has been adjusted press the corresponding + and ­ buttons simultaneously; if this procedure is not performed the new setting will not be saved. Once the adjustment procedures have been completed for the various burners, press the T2, T5 and T9 buttons simultaneously (in this case the T2 button should be pressed slightly before the other two); hold the buttons down for approximately 5 seconds, until the hob returns to the status of being NOTE: if none of the buttons on the keypad are pressed for more than 1 minute during the adjustment stage, the appliance exits the function automatically. SAFETY TIMES FOR EACH BURNER: The safety time when the appliance is switched off (the interval between the flame being switched off and subsequent P. The safety time (the interval between the opening of the valve and its closure if no flame is detected; this coincides with the maximum spark duration) is 6 seconds. BREAKDOWN SITUATIONS AND RESULTING BEHAVIOUR OF THE APPLIANCE: 1 - Flame monitoring device breakage: the burner cannot remain lit and therefore enters its safety mode. The burner may be operating already or still switched off (it can only be switched on after the cooking duration has been set). To select and set this option: Press button T3; windows D3, 4, 5 and 6 flash alternately, displaying the symbol "t" and window D2 displays the figure "99" (the maximum time value which may be set). select the desired burner using + or -; Use timer buttons T3 and T4 to set the desired cooking time. The power level indication appears on the "timed" burner as usual (although this may be modified during the operating period), interrupted every 10 seconds by the indication t; At the end of the operating period, the burner switches off and a buzzer sounds; Select the most suitable burner in accordance with the diameter of the cookware you wish to use. the oo symbols in the control area (M) indicate the position of the relevant burner on the hob. The burners have thermocouple safety devices which offer protection against gas leaks. if the burner flame is extinguished during operation , the ignition device is activated in an attempt to re-ignite the flame. If this fails, after less than 6 seconds, the flow of gas to the burner is blocked and the corresponding display shows the text "F2". Do not attempt ignition again for at least 1 minute, so that the escaped gas in the vicinity of the burner is able to disperse properly. In some cases the non-ignition of a burner may be due to air which has become trapped in the gas piping. [. . . ] ⷠIf the appliance breaks down, under no circumstances should you attempt to perform the repairs yourself. Repairs carried out by inexperienced persons may cause injury or further malfunctioning of the appliance. Always make sure that pan handles are turned towards the centre of the hob in order to avoid accidental burns. ⷠDo not close the glass cover (if present) while the gas burners or electric hotplates are still hot. [. . . ]