User manual SKIL 0502

[. . . ] [. . . ] 23 oldal 24 strana 26 sayfa 28 PL RU UA GR RO BG SK HR SCG SLO EST LV LT INSTRUKCJA O INSTRUCØIUNI strona 29 31 33 35 pagina 37 YKA3A POKYNY UPUTE UPUTSTVA NAVODILA INSTRUKCIJA INSTRUKCIJA 38 strana 40 stranica 42 stranica 43 stran 45 lappuse 48 puslapis 50 KASUTUSJUHEND lehekülg 46 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 08/06 2610395382 1 2 3 H N A C B D L K G M F J 4 5 E 2 6 B 7 C 8 G 3 9 H 0 J 4 ! K @ L 1 2 5 # K K M $ N % 6 GB Multi-surface leveling laser INTRODUCTION 502 J K L M N Pin accessory Magnet accessory Screw accessory Pivot accessory Belt clip accessory This tool is intended for aligning objects and/or marking desired cutting lines by means of a straight laser line projection; with the accessories supplied the tool can be used on a variety of surfaces Carefully read this instruction manual as well as the warning label on the tool, before you use the tool 1 Pay special attention to the safety instructions and warnings; failure to follow these may result in serious (eye) injury Before using the tool for the first time, paste the supplied sticker in your national language over the English text of warning label F 3 Save this instruction manual for future reference USE TECHNICAL SPECIFICATIONS Laser type Laser class Maximum power output Power supply Operating temperature Storage temperature Weight Accuracy 635 nm 2 1 mW 3 x AG13 button cell battery -10°C to 40°C -20°C to 60°C 0, 05 kg deviation of +/- 10 mm at 5 metres' distance SAFETY Do not look into the laser beam (laser radiation) 2 Do not point the laser beam at persons or animals Do not place the tool in a position that may cause anyone to look into the laser beam intentionally or unintentionally Do not use any magnifying optical tools (such as magnifying glasses, telescopes, or binoculars) to view the laser beam Do not remove or damage the warning label on the tool Do not operate the tool in the presence of flammable liquids, gases or dust Do not operate the tool with children around This tool should not be used by people under the age of 16 years Do not use the tool for any purpose other than those mentioned in this instruction manual Only use the original accessories which are intended for this tool Always switch off the tool when not in use TOOL ELEMENTS 3 A B C D E F G H On/off switch Bubble level for horizontal lines Bubble level for vertical lines Laser light opening Battery compartment cover Warning label Suction accessory Clamp accessory 7 On/off - before first use, remove protective insert as illustrated 4 - switch on/off the tool by pushing switch A !ensure that the tool is switched off - remove cover E - insert 3 x AG13 button cell battery (pay attention to correct polarisation) - mount cover E - always remove the batteries from the tool, if the tool is not used for a long period - always replace the complete set of batteries Operating the tool 6 - when projecting a horizontal line, ensure that the bubble in level B is centered - when projecting a vertical line, ensure that the bubble in level C is centered - make measurements using the projected line as reference - when projecting a laser line at a longer distance, you may increase its visibility by placing an object at the end of the desired distance 7 Suction accessory G 8 For projecting lines on smooth surfaces - slide tool on accessory G - place accessory G onto surface - level the tool (ensure that the bubble in the relevant level is centered) - push 2 knobs - use projected line as reference Clamp accessory H 9 For projecting lines on board materials (thickness 15 30 mm) - slide tool on accessory H - fasten accessory H onto board by turning knob clockwise - use projected line as reference Pin accessory J 0 For projecting lines on plasterboard, soft wood, and other soft materials - slide tool on accessory J - place accessory J onto surface - level the tool (ensure that the bubble in the relevant level is centered) - push 2 knobs - use projected line as reference !For projecting lines on any ferrous metal surface or profile - slide tool on accessory K - place accessory K onto surface - level the tool (ensure that the bubble in the relevant level is centered) - use projected line as reference Screw accessory L @ For projecting lines at the same level as already mounted screw - place accessory L over already mounted screw - slide accessory L to the left/right, so that screw ends up firmly in tapered end of peg - slide tool on accessory L - level the tool (ensure that the bubble in the relevant level is centered) - use projected line as reference for mounting other screw(s) Screw accessory L can also be used in combination with tape or drawing-pins Pivot accessory M # For projecting lines at an angle (for rough indication only) - remove knob by turning it counter-clockwise - slide tool on magnet accessory K - fasten magnet accessory K on accessory M by turning knob clockwise - move tool over graduated arc by loosening/fastening knob Pivot accessory M can also be used in combination with tape or drawing-pins Belt clip accessory N $ For easy and convenient storage F Niveau laser toutes surfaces INTRODUCTION 502 Cet outil est conçu pour aligner des objets et/ou marquer des lignes de coupe par projection d'un faisceau laser; les accessoires fournis permettent de l'utiliser sur les surfaces les plus diverses Lisez soigneusement ce mode d'emploi ainsi que l'étiquette d'avertissement située sur l'outil avant d'utiliser l'outil 1 Prêtez attention aux consignes de sécurité et aux avertissements; sinon, vous risquez d'endommager gravement vos yeux Avant d'utiliser cet outil pour la première fois, collez l'autocollant fourni dans votre langue sur le texte anglais de l'étiquette d'avertissement F 3 Conservez ce mode d'emploi pour vous y reporter à l'avenir SPECIFICATIONS TECHNIQUES Type de laser Catégorie de laser Puissance de sortie maximale Alimentation Température en fonctionnement Température d'entreposage Poids Exactitude 635 nm 2 1 mW 3 piles plates AG13 -10°C à 40°C -20°C à 60°C 0, 05 kg déviation de +/- 10 mm à une distance de 5 mètres MAINTENANCE Do not expose the tool to continuous vibration or extremely hot or cold temperatures Always store the tool indoors in its protective carton/case Always keep the tool free of dust, moisture and direct sunlight Clean the tool with a damp cloth and mild soap !always remove the batteries before cleaning the lens Do not disassemble or modify the tool in any way Do not attempt to change any part of the laser lens SECURITE GUARANTEE / ENVIRONMENT This Skil product is guaranteed in accordance with statutory/country-specific regulations; damage due to normal wear and tear, overload or improper handling will be excluded from the guarantee In case of a complaint, send the tool undismantled together with proof of purchase to your dealer or the nearest Skil service-station (addresses as well as the service diagram of the tool are listed on www. skileurope. com) Do not dispose of electric tools, batteries, accessories and packaging together with household waste material (only for EU countries) - in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility - symbol % will remind you of this when the need for disposing occurs 8 Ne projetez pas le rayon laser dans vos yeux (rayonnement laser) 2 Ne dirigez pas le rayon laser vers des personnes ou des animaux Ne placez pas cet outil dans une position où le rayon laser pourrait atteindre l'oeil d'une personne, volontairement ou non N'utilisez pas d'outils optiques grossissants (loupes, télescopes ou jumelles) pour voir le rayon laser Veillez à ne pas enlever l'étiquette d'avertissement de l'outil ni à l'endommager N'utilisez pas cet outil en la présence de liquides inflammables, de gaz ou de poussière N'utilisez pas cet outil en la présence d'enfants Cet outil ne doit pas être utilisé par des personnes de moins de 16 ans N'utilisez pas cet outil dans un but autre que ceux mentionnés dans ce mode d'emploi Utilisez seulement les accessoires d'origine prévus pour cet outil Mettez toujours l'outil hors tension lorsqu'il n'est pas utilisé [. . . ] [. . . ]