User manual SKIL 1024

[. . . ] IMPACT DRILL 1024 (F0151024. . ) GB F D NL S DK N FIN E P I H CZ TR PL RU ORIGINAL INSTRUCTIONS UAGB NOTICE ORIGINALE ORIGINALBETRIEBSANLEITUNG D ORIGINELE GEBRUIKSAANWIJZING NL BRUKSANVISNING I BG S ORIGINAL ORIGINAL BRUGSANVISNING DK ORIGINAL BRUKSANVISNING N GR RO F 10 14 17 20 23 26 29 32 35 38 41 45 48 51 54 8 UA GR RO BG SK HR INSTRUCIUNI DE FOLOSIRE ORIGINALE PÔVODNÝ NÁVOD NA POUZITIE ORIGINALNE UPUTE ZA RAD 58 61 65 68 72 75 78 81 84 87 101 90 SK HR ALKUPERÄISET OHJEET FIN SRB MANUAL ORIGINAL E SLO MANUAL ORIGINAL P EST ISTRUZIONI ORIGINALI I LV EREDETI HASZNÁLATI UTASÍTÁS H LT PVODNÍM NÁVODEM K POUZÍVÁNÍ CZ AR ORJNAL LETME TALMATI TR FA INSTRUKCJA ORYGINALNA PL RU SRB ORIGINALNO UPUTSTVO ZA RAD SLO IZVIRNA NAVODILA EST ALGUPÄRANE KASUTUSJUHEND LV LT AR FA ORIINL LIETOSANAS PAMCBA ORIGINALI INSTRUKCIJA AR AR FA FA 99 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 12/10 2610Z02062 1 1024 900 Watt 0-1100 0-2800 0-17600 p/min 0-44800 p/min 2 2 3 5 4 6 7 C 8 3 9 A 0 4 ! @ 5 # $ PHILLIPS POZIDRIV SLOTTED 6 % ^ & * ( 7 INTRODUCTION Impact drill 1024 · This tool is intended for impact drilling in brick, concrete and stone as well as for drilling in wood, metal, ceramic and plastic; tools with electronic speed control and left/ right rotation are also suitable for screwdriving and thread cutting · Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 A B C D E F G H TOOL ELEMENTS 2 Switch for on/off and speed control Button for switch locking Wheel for maximum speed control Switch for changing direction of rotation Gear selector Switch for selecting drilling function Auxiliary handle Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. [. . . ] Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. This enables better control of the power tool in unexpected situations. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. [. . . ] select drilling function only when tool is switched off and plug is disconnected Changing bits !do not use bits with a damaged shank Adjusting drilling depth @ · Holding and guiding the tool # - always use auxiliary handle G 2 (can be adjusted as illustrated) !while working, always hold the tool at the grey-coloured grip area(s) - keep the ventilation slots uncovered - do not apply too much pressure on the tool; let the tool do the work for you · Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL · Use the appropriate bits $ ! [. . . ]