User manual SKIL 3310

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SKIL 3310. We hope that this SKIL 3310 user guide will be useful to you.


SKIL 3310 : Download the complete user guide (3040 Ko)

You may also download the following manuals related to this product:

   SKIL 3310 PARTS LIST (79 ko)

Manual abstract: user guide SKIL 3310

Detailed instructions for use are in the User's Guide.

[. . . ] WARNING "READ ALL INSTRUCTIONS" Failure to follow the safety rules listed below and other basic safety precautions may result in serious personal injury. AVOID ACCIDENTAL STARTING Make sure the switch is in the "OFF" position before plugging in tool. nEVER STAND ON TOOL OR ITS STAND Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Do not store materials on or near the tool such that it is necessary to stand on the tool or its stand to reach them. [. . . ] Press down on the guard release lever 5 until you feel and hear it snap into the locking position. While pulling out the attachment pin 8, attach the AntiKickback Device 9 into the flat recessed area 10 of the riving knife 2 (Fig. Slide the Anti-Kickback Device down until it drops into the recessed area ­ then release the attachment pin such that the Anti-Kickback Device locks onto the riving knife immediately behind the guard assembly. Carefully raise and lower the pawls 11 ­ when letting go, the spring-loaded pawls must come down and contact the table insert (Fig. Note: The two attachments are independent of each other, so the Anti-Kickback Device can be attached before the Guard Assembly. Position the rip fence 4 over table, holding up the front end while engaging rear, then lowering front end onto rail. NOTE: Use the screws 1, washers 2, and lock nuts 3 supplied in the hardware kit to attach the pieces of the leg stand together (Fig. Do not tighten the hardware completely until the leg stand is completely assembled. The following letters are stamped on pieces for identification: A - Legs (qty. NOTE: Mount the table saw to the leg stand using the hardware supplied in the hardware kit. Place the table saw onto the assembled leg stand so that the four (4) mounting holes 4 in the base of the saw are over the four (4) mounting holes in the front and rear top plates 5 (Fig. Secure the table saw to the leg stand using four (4) bolts 6, washers 7, and lock nuts 8. When mounting the table saw to the leg stand, DO NOT overtighten the mounting hardware. WARNING table saw to stand and entire unit must be placed on solid, level surface. WARNING Do not stand on table saw sand or use as ladder or scaffolding. If table saw is to be used in a permanent location, it should be fastened securely to a firm supporting surface such as a stand or workbench, using the four mounting holes, 1 two of which are shown (Fig. When mounting table saw to a workbench or plywood, holes should be drilled through the supporting surface of the workbench or plywood and a opening MUST be made the same size as the opening in the bottom of the saw using the dimensions illustrated (Fig. Each of the four mounting holes should be bolted securely using 5/16" hex nuts (not included). Screw lengths should be 2-1/2" longer than the thickness of the bench top. Place table saw on workbench aligning holes in base with holes drilled in workbench. An alternative method of securing your table saw is to fasten the saw base to a mounting board 24" x 24" minimum size to prevent saw from tipping while in use. Any good grade of plywood with a 3/4" minimum thickness is recommended. [. . . ] Frequently blow out any dust that may accumulate inside the saw cabinet and the motor. The cord and the tool should be wiped with a dry clean cloth to prevent deterioration from oil and grease. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents which contain ammonia. Avoiding use of these and other types of cleaning agents will minimize the possibility of damage. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SKIL 3310




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SKIL 3310 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.