User manual SKIL 3315

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SKIL 3315. We hope that this SKIL 3315 user guide will be useful to you.


SKIL 3315 : Download the complete user guide (2237 Ko)

You may also download the following manuals related to this product:

   SKIL 3315 PARTS LIST (87 ko)

Manual abstract: user guide SKIL 3315

Detailed instructions for use are in the User's Guide.

[. . . ] ) symbol listed BELOW and other safety precautions, may result in serious personal injury. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Keep bystanders, children and visitors away while operating a power tool. Store idle tools out of reach of children and other untrained persons. [. . . ] Miter lock Knob -- The miter lock knob locks the miter saw table at any desired miter angle. Tool mounting pads -- Four areas to clamp, bolt or nail the saw to a flat work surface. Never reach around or in the back of the saw blade Hold or clamp workpiece against base and fence. After turning saw OFF, keep saw in the down position and wait for blade to stop before removing cutoff pieces or changing settings. To avoid electrical shock, do not expose to rain or use in damp locations. To reduce the risk of injury, always use the clamp to support the workpiece when making a compound miter cut. Never reach around or in the back of the saw blade Hold or clamp workpiece against base and fence. After turning saw OFF, keep saw in the down position and wait for blade to stop before removing cutoff pieces or changing settings. To avoid electrical shock, do not expose to rain or use in damp locations. To reduce the risk of injury, always use the clamp to support the workpiece when making a compound miter cut. Separate all parts from packing materials and check each one with the parts in Figure 1 to make sure all items are accounted for before discarding any packing material. Never carry the tool by the cord or head assembly power switch handle. If any parts are missing, do not plug in power cord or turn the switch on until the missing parts are obtained and are installed correctly. Should be no Gap or Overlap when Square is Flipped Over in Dotted Position Disconnect plug from power source before performing any assembly, adjustment or repair to avoid possible Draw Light Tracez une ligne délicateon Board Line sur la planche leAlong this Edge long de ce bord. Should beavoirGap or Overlap Il ne doit y no aucun écartement when Square is Flipped Over in ou chevauchement lorsque l'équerre Dotted Position position en tirets. Carefully thread the miter lock knob 1 into the hole 2 located at the front of the miter table (Figure 2). Loosen handle 1/4 turn or more and press down on the miter handle release 3 to unlock the miter table from the set position. With the miter arm locked in the down position, compress the two tabs on the spring clip and slide the bag over the rib on the dust port (Figure 5) then release the tabs. Position dust bag so that it does not interfere with the tool during the cutting operation for all miter/bevel settings. Be extremely careful of dust disposed, materials in fine particle form may be explosive. Spontaneous combustion, may in time, result from mixture of oil or water with dust particles. When sawing chemically pressure treated lumber, paint that may be lead based, or any other materials that may contain carcinogens, use special precautions. [. . . ] Rods have a tendency to roll while being cut, causing the blade to "bite" and pull the work with your hand into the blade (Figure 33). Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SKIL 3315




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SKIL 3315 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.