User manual SKIL 3385-01

[. . . ] "READ ALL INSTRUCTIONS" Failure to follow the safety rules listed below and other basic safety precautions may result in serious personal injury. DISCONNECT TOOLS FROM POWER SOURCE When not in use, before servicing, when changing blades, bits, cutters, etc. KEEP GUARDS IN PLACE In working order, and in proper adjustment and alignment. REMOVE ADJUSTING KEYS AND WRENCHES When not in use, before servicing, when changing blades, bits, cutters, etc. [. . . ] Use only 3-wire extension cords which have 3-prong grounding type plugs and 3-pole receptacles which accept the tool's plug. Your unit is for use on 120 volts; it has a plug that looks like the one in Figure 1. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Before connecting the motor cord to power source, make certain the switch is in the "OFF" position and be sure the electric current is of the same characteristics as stamped on the band saw nameplate. This machine must be grounded while in use to protect the operator from electric shock. Plug power cord into a 110-120V properly grounded type outlet protected by a 15-amp dual element time delay fuse or circuit breaker. 1 , is properly grounded; have it checked by a qualified electrician. To avoid electric shock, do not touch the metal prongs on the plug when installing or removing the plug to or from the outlet. Failure to properly ground this power tool can cause electrocution or serious shock, particularly when used near metal plumbing or other metal objects. If power cord is worn, cut or damaged in any way, have it replaced immediately to avoid shock or fire hazard. To reduce the risk of injury, never connect plug to power source outlet until all assembly steps are complete and until you have read and understood the entire owner's manual. Check each one with the "Table of Loose Parts" to make sure all items are accounted for before discarding any packing material. If any parts are missing, do not attempt to assemble the band saw, plug in power cord or turn the switch on until the missing parts are obtained and are installed correctly. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Blade tension knob Blade tension quick release handle LED work light Blade Table support assembly Lower blade guide Drive belt 9 Lower wheel Door Reset button Upper wheel Blade tracking lock knob Blade tracking knob Motor assembly Base Dust port Table tilt adjustment lock knob Table tilt adjustment knob 19 20 21 22 23 24 25 26 27 28 29 Table Upper blade guide Upper blade guide lock knob Upper blade guide adjustment knob Upper viewing port Upper door latch Laser line adjustment knob Lower door latch ON/OFF switch with safety key Laser switch Work light switch Before assembling the band saw, turn off the saw, remove the safety key and unplug the power cord from the electrical outlet. The power cord must remain unplugged whenever you are working on the saw. Loosen the locking knob (1) and rotate the blade guard knob (2) to raise the upper blade guard (3) to the highest position. Place the table on the table support by sliding the slot (4) in the table over the blade (5), taking care not to damage the blade. Align the four holes on the bottom of the table over the four holes in the table support (6). Place a washer and locking washer on each bolt (7) and secure the bolt through the table support and into the table. It is possible to replace the blade with the table in place, however, it may be easier to remove the table before replacing the blade. [. . . ] The smallest diameter circle that can be cut is determined by the width of the blade. For longest wear and best cutting results, use the correct blade thickness, width, and temper for the type of material you will cut. For cutting wood and similar materials with this band saw, purchase blades in widths up to 3/8" (9. Power switch "OFF" and remove plug from the power source outlet before maintaining or lubricating your band saw. [. . . ]