User manual SPYKER 64
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SPYKER 64. We hope that this SPYKER 64 user guide will be useful to you.
Manual abstract: user guide SPYKER 64
Detailed instructions for use are in the User's Guide.
[. . . ] Then install side bolts, and tighten all bolts securely.
*model 34 only
CAUTION -- at this point make certain assembly is correct. Then install wheel retainers (25) by taping firmly with a hammer (Once installed, removal is nearly impossible. )
White Nylon Washer
45
9.
Install the handle grips (33) on handle. For easier installation, grips may be lubricated with water only.
Note: model 54 has a black plastic hopper.
45
45
10. Connect
T-handle to center section using 4 (1) 11/ " bolt and nut.
Note: Center sections is being obsoleted. Your spreader may not contain one.
3
4
Spreader Assembly Read Before Using
Read Before Using
11.
Connect ground prop to center section 4 using (1) 11/ " bolt and nut. [. . . ] The spread thins or feathers at the outer edges, eliminating sharp, "Edge of spread" lines which cause stripes and streaks. Extra coverage can be given under trees and other heavy feeding areas without showing "edge of spread" lines. WARNING: When spreading products containing herbicides, exercise extreme caution with respect to careless spreading and to wind-drift. If a dial setting is not found, use the size and weight comparison table found on the back page. If the setting proves to be too low, cover the area more than one time. A higher setting can be used when a proven dial setting is established. The operation of the spreader, the condition of the material (damp or dry or over-pulverized) and weather conditions, are all contributing factors. For these reasons, it's often a good idea to spread the area 2 times - at one-half rate in cross directions (SEE INFORMATION ON ONE-HALF RATE DIAL SETTINGS ON REFERENCE CHART ON THE BACK PAGE. SPREADING AT ONE-HALF RATE DIAL SETTINGS IS HIGHLY RECOMMENDED UNDER DAMP & HUMID CONDITIONS. BECOME FAMILIAR WITH THE OPERATION OF THE SPREADER BEFORE YOU PUT MATERIAL IN THE HOPPER. Practice walking with the spreader, opening and closing the rate gate at the appropriate times. Remember: Open the rate gate after the spreader is in motion at operating speed (about 3 mph. , or at a brisk walking pace). Close the rate gate while spreader is still at operational speed.
Model 54 Only 43 44 45 05-46-0500 05-94-0065 05-94-0064 1 1 3 Plastic Hopper Cover, Clear Plastic with Black Washer, Plastic
Model 34 Only 46 47 48 49 50 51 Optional 52 53 54 55 05-82-0000 05-99-0021 SL-EH-1005 05-94-0065 Extension Hopper Cover - Model 64 & 34 Screen Cover - Model 54 SS-97-0006 SL-HP-1044 99-50-1081 05-97-0008 SS-95-0004 05-24-1070 1 2 1 1 1 Axle 18 3/4" Long Drilled Axle, Gears, Gear Box, Spinner Assembly Axle, Cotter Pin Spinner Shaft 3/8 x 6 1/2 Pneumatic 8. 5 x 3. 5 Hand Hold
Rotary Agitator
Use the rotary agitator only if needed. - See page #8.
OIL BEARINGS AND ALL MOVING PARTS
Make certain the spreader is running freely!
Model 30 Only 56 57 05-54-0004 05-300-0500 1 1 Spinner Shaft Hopper
9
10
Read Before Using
Now You are Ready to Put Material in the Hopper
· · · · Make certain the rate gate is in closed position. As insurance against spill damage and spill loss, put material in the hopper with the spreader on a walk, driveway, paper, plastic, etc. Or for added capacity, the inverted bag in the hopper can serve as a capacity extension. Also, an extension hopper, complete with filtering and pulverizing screen, is available from the manufacturer. CONDITION
Spreader Assembly
Spreader pushes hard: 1 3 4 LOOK FOR . [. . . ] (Newton's law of motion: To every action there is always an opposed and equal reaction. ) Serviceability - 24 hour replacement parts service available direct from the factory. Series 22 spreaders shipped set up except hand hold/bump bar and push handle or tractor pull bar.
Manufacturer and Product
Bent Grass or Red Top
Bag Weight 0. 5# 1# 2# 0. 5# 1# 2# 2# 3# 4# 2# 4# 6# 2# 4# 6# 4 oz. Coverage 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000
1. 25 2. 0 2. 5 2. 5 3. 0 3. 5 2. 75 3. 0 3. 25 6. 0 7. 0 7. 0 6. 0 7. 0 7. 75 1. 9 2. 1 2. 5 4. 5 4. 75 5. 0
Park, Merion, Delta, or Kentucky Bluegrass
Hulled Bermuda
Mixtures including coarse seeds
Rye Grasses or Tall Fescue
Dichondra
Pensacola Bahia
1 YEAR LIMITED WARRANTY
This is warranted to the original purchaser only, other than used commercially, against defects in materials and workmanship, for a period of one year from the date of purchase. *For Spyker Spreaders LLC, products employing metal gear systems, pinion and bevel, these metal gears, only, not inclusive of any other parts or materials, are warranted for the life of the spreader, not to be used for replacement or repair past original purchase. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SPYKER 64
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SPYKER 64 will begin.