User manual TENDA W311R

[. . . ] 11N Wireless Broadband Router 1 11N Wireless Broadband Router Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co. , Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co. , Ltd. Without the permission of Shenzhen Tenda Technology Co. , Ltd, any individual or party is not allowed to copy, plagiarize, imitate or translate it into other languages. [. . . ] The users only enter PIN code or press WPS button on the panel to configure it without selecting encryption method and secret keys by manual. In the "Wireless settings" menu, click "WPS settings" to enter the next screen. WPS settingsTo enable or disable WPS function. 42 11N Wireless Broadband Router WPS modeProvide two ways: PBC (Push-Button Configuration) and PIN code. PBCSelect the PBC or press the WPS button on the front panel of the device for about one second (Press the button for about one second and WPS indicator will be blinking for 2 minutes, which means the WPS is enabled. During the blinking time, you can enable another device to implement the WPS/PBC negotiation between them. Two minutes later, the WPS indicator will be off, which means the WPS connection is completed. At present, the WPS supports up to 32 clients access. ) PINIf this option is enabled, you need to enter a wireless client's PIN code in the field and keep the same code in the WPS client. WPS Summary Show the current state of Wi-Fi protected setting, including authorized mode, encryption type, default key and other information. Start MSC process means the process has been started and waits for being connected. Configured means the negotiation is successful between server and clients. WPS Configured "yes" means WPS feature is enabled and goes into effect. Usually the AP-security has been enabled, here will displayed "not used". Mode The authorization mode deployed by WPS, generally WPA/WPA2-personal mode. Reset OOB When this button is pressed, the WPS client will be idle state, and WPS indicator will be turned off. AP will not respond the WPS client's requests and the set the security mode as WPA mode. 6. 5 WDS Settings WDS (Wireless Distribution System) is used to expand wireless coverage area. This Router provides three modes: Lazy, Bridge and Repeater. 44 11N Wireless Broadband Router Lazy: In this mode, the connected device can be Bridge mode or Repeater mode and enter the Router's BSSID to establish the connection. Bridge: You can wirelessly connect two or more wired networks via this mode. In this mode, you need to add the Wireless MAC address of the connecting device into the Router's AP MAC address table or select one from the scanning table. Repeater ModeIn this mode, add the opposing MAC address into each own AP MAC address table by manual or scanner to enlarge and extend the wireless radio. AP MAC: Input the MAC address of another (opposing) wireless router you want to connect. NOTE: It is recommended that two wireless routers keep the same bandwidth, channel number, and security settings. Apply the settings and reboot the Router to activate it. 45 11N Wireless Broadband Router 6. 6 Wireless Access Control To secure your wireless LAN, the wireless access control is actually based on the MAC address management to allow or block the specific clients to access the wireless network. [. . . ] The changing key makes it much more 83 11N Wireless Broadband Router difficult for a hacker to learn the key and gain access to the network. WPA2 is the second generation of WPA security and provides a stronger encryption mechanism through Advanced Encryption Standard (AES), which is a requirement for some government users. 84 11N Wireless Broadband Router Appendix 2: Ask and Question In this part some questions and problems shown during the Router's usage and installation will be given suggesting answers. If your problems are not in the list, please log into our website www. tenda. cn or send an E-mail to support@tenda. cn, and we will reply you in the first time. 1Can not login to the Web interface of the Router after you enter the IP address in the address field Step 1: check the Router if it works well. Once the device is powered on for a few seconds, the SYS indicator on the panel will be turned on. Step 2: check the network cables if it is good and the corresponding indicator is "Always ON". [. . . ]