User manual TRICITY CPW1000
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TRICITY CPW1000. We hope that this TRICITY CPW1000 user guide will be useful to you.
Manual abstract: user guide TRICITY CPW1000
Detailed instructions for use are in the User's Guide.
[. . . ] · Only use products (detergent, salt and rinse aid) suitable for dishwashers. · Avoid opening the door whilst the appliance is in operation, hot steam may escape. · Do not take any dishes out of the dishwasher before the end of the dishwashing cycle. · After use, isolate the appliance from the power supply and turn off the water supply. [. . . ] Adjust the rinse aid dosage
7
Set the water softener
The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. The higher the content of these minerals and salts, the harder your water is. Water hardness is measured in equivalent scales, Clarke degrees, French degrees (°TH)
Water hardness Clarke 64 - 88 53 - 63 46 - 52 36 - 45 28 - 35 23 - 27 18 - 22 13 - 17 5 - 12 <5 °TH 91 - 125 76 - 90 65 - 75 51 - 64 40 - 50 33 - 39 26 - 32 19 - 25 7 - 18 <7 mmol/l 9, 0- 12, 5 7, 6 - 8, 9 6, 5 - 7, 5 5, 1 - 6, 4 4, 0 - 5, 0 3, 3 - 3, 9 2, 6 - 3, 2 1, 9 - 2, 5 0, 7 - 1, 8 < 0, 7
and mmol/l (millimol per litre - international unit for the hardness of water). The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting the water hardness setting manually 2 2 2 2 2 2 1 1 1 1 electronically level 10 level 9 level 8 level 7 level 6 level 5 level 4 level 3 level 2 level 1
Use of salt
yes yes yes yes yes yes yes yes yes no
The water softener must be set in both ways: manually, using the water hardness dial and electronically.
8
Setting the water softener manually (see table)
The water softener is factory set at position 2.
Set switch to position 1 or 2
Setting the water softener electronically (see table)
The water softener is factory set at position 5. Press and hold the start/cancel button and turn the programme selector dial clockwise till the first programme. Keep the button pressed until the On/Off indicator light and the start/cancel indicator light start flashing. The end of programme indicator light might flash 5 times, for example. To memorise the operation, turn the programme selector dial to position off.
Use of dishwasher salt
CAUTION!Use only special salt suitable for dishwashers.
9
Unscrew the cap.
Only before filling with Using the funnel provided, salt for the first time, fill pour in the salt until the the salt container with wa- container is filled with salt. Water will overflow from the container as salt is added.
Remove any trace of salt. 15
Clean filters A, B and C Turn the handle about 1/4 Remove filter A from the thoroughly under running turn anticlockwise and re- base of the washing comwater. move filters B and C.
Replace the filters and lock by turning the handle clockwise to the stop.
Cleaning the spray arms
NEVER try to remove the spray arms. If residues of soil have clogged the holes in the spray arms, remove them with a cocktail stick.
Internal cleaning
Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run the wash programme for heavy soiled dishes using detergent but without dishes.
External cleaning
Clean the external surfaces of the machine and control panel with a damp soft cloth. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc. . . . ).
Prolonged periods of nonoperation
If you are not using the machine for any prolonged period of time you are advised to: 1. Leave the door ajar to prevent the formation of any unpleasant smells. Leave the inside of the machine clean.
Frost precautions
Avoid placing the machine in a location where the temperature is below 0°C. If this is unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it.
1. Avoid over tilting the machine during transportation.
Moving the machine
If you have to move the machine (moving house etc. . . . ):
Environmental concerns
Packaging material
The packaging materials are environmentally friendly and can be recycled. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. When a unit is no longer being used: · Pull the plug out of the socket. [. . . ] Only use, for connection to the water mains, new hose-set; old hose-set must not be reused. If the machine is connected to new pipes or pipes which have not been used for a long time,
you should run the water for a few minutes before connecting the inlet hose.
Inlet hose
Connect the inlet hose to a water tap with an external thread of 3/4". The inlet hose can be turned either to the left or the right to suit the installation by means of the locknut. The locknut must be correctly fitted to avoid water leaks.
Drain hose
Connect drain hose to the Required height: 30 to 100 Ensure that the hoses are When connecting the sink. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TRICITY CPW1000
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TRICITY CPW1000 will begin.