User manual ZEBRA Z4MPLUS

[. . . ] Z4Mplus/Z6Mplus Industrial/Commercial Printer User Guide © 2007 ZIH Corp. The copyrights in this manual and the software and/or firmware in the label printer described therein are owned by ZIH Corp. Unauthorized reproduction of this manual or the software and/or firmware in the label printer may result in imprisonment of up to one year and fines of up to $10, 000 (17 U. S. C. 506). This product may contain ZPL®, ZPL II®, and ZebraLinkTM programs; Element Energy Equalizer® Circuit; E3®; and Monotype Imaging fonts. [. . . ] Note · Code Page 850 requires the data bits to be set to 8 bits. Default: 8 BITS Selections: 7 BITS, 8 BITS To change the value shown: 1. Press SELECT to accept any changes and deselect the parameter. PARITY NONE + Set Parity The parity of the printer must match the parity of the host computer for accurate communications to take place. Select the parity that matches the one being used by the host computer. Default: NONE Selections: EVEN, ODD, NONE To change the value shown: 1. Press SELECT to accept any changes and deselect the parameter. HOST HANDSHAKE XON/XOFF + Set Host Handshake The handshake protocol of the printer must match the handshake protocol of the host computer for communication to take place. Select the handshake protocol that matches the one being used by the host computer. Default: XON/XOFF Selections: XON/XOFF, DTR/DSR, RTS/CTS To change the value shown: 1. Press SELECT to accept any changes and deselect the parameter. 13163L-002 A Z4Mplus/Z6Mplus User Guide 9/18/07 Configuration Control Panel Parameters 95 Table 11 · Printer Parameters (Page 14 of 22) Parameter Action/Explanation PROTOCOL NONE + Set Protocol Protocol is a type of error checking system. Depending on the selection, an indicator may be sent from the printer to the host computer signifying that data has been received. Further details on protocol can be found in the ZPL II Programming Guide. Default: NONE Selections: NONE, ZEBRA, ACK_NAK Note · ZEBRA is the same as ACK_NAK, except that ZEBRA response messages are sequenced. If ZEBRA is selected, the printer must use DTR/DSR for host handshake protocol. To change the value shown: 1. Press SELECT to accept any changes and deselect the parameter. NETWORK ID 000 + Set Network ID Network ID is used to assign a unique number to a printer. Press SELECT to accept any changes and deselect the parameter. 9/18/07 Z4Mplus/Z6Mplus User Guide 13163L-002 A 96 Configuration Control Panel Parameters Table 11 · Printer Parameters (Page 15 of 22) Parameter Action/Explanation COMMUNICATIONS - NORMAL MODE + Set Communications Mode The communication diagnostics mode is a troubleshooting tool for checking the interconnection between the printer and the host computer. When DIAGNOSTICS is selected, all data sent from the host computer to the printer prints as straight ASCII characters, with the hex value below the ASCII text. The printer prints all characters received, including control codes, like CR (carriage return). A sample printout is shown in Communications Diagnostics Test on page 138. Notes on diagnostic printouts are defined as follows: · FE indicates a framing error. Default: NORMAL MODE Selections: NORMAL MODE, DIAGNOSTICS To change the value shown: 1. Set the print width equal to or less than the label width used for the test. Press SELECT to accept any changes and deselect the parameter. CONTROL PREFIX < >7EH + Set Control Prefix Character The printer looks for this two-digit hex character to indicate the start of a ZPL/ZPL II control instruction. [. . . ] The arbitration proceeding will take place in Chicago, Illinois and be conducted in the English language. The arbitration panel will consist of 3 arbitrators, one arbitrator appointed by each party and a third neutral arbitrator appointed by the two arbitrators designated by the parties. Any communication 13163L-002 A Z4Mplus/Z6Mplus User Guide 9/18/07 End User License Agreement 161 between a party and any arbitrator will be directed to the AAA for transmittal to the arbitrator. The parties expressly agree that the arbitrators will be empowered to, at either party's request, grant injunctive relief. [. . . ]